St37-2 steel plate

-

St37-2 steel plate basic performance requirements


With the continuous improvement of production technology, engineering buildings put forward higher and higher requirements for St37-2 steel plate. Katalor as a professional St37-2 steel plate supplier and exporter in China. We have our own team to produce the St37-2 steel plate.

St37-2 steel plate is mainly used in car manufacturing. In order to meet the requirements of automobile safety, crashworthiness and seismic resistance, the St37-2 steel plate should have high tensile strength, impact absorption performance and fatigue strength.

At the same time, in order to improve the St37-2 steel plate formability and surface quality, it is necessary to have lower plane anisotropy and higher elongation, plastic strain ratio, wrinkle resistance, etc in St37-2 steel plate.

Therefore, the production of the St37-2 steel plate is very difficult to control, it not only requires lower silicon carbon content, higher acid soluble aluminum content and lower inclusion content and shape, but also has strict requirements for the shape of the plate and hot rolling. The properties and metallographic structure of the St37-2 steel plate have special requirements.

We can find the St37-2 steel plate basic performance requirements are very important for the quality. And you can contact us if you are interested in St37-2 steel plate. We will give you the best choose in St37-2 steel plate. Of course we will send the St37-2 steel plate detail information for you.

           katalorsteels@gmail.com

评论

发表评论

此博客中的热门博文

ASTM A517 steel belongs to the boiler steel plate

-
ASTM A517 steel (also called ASME SA517 standard) is a kind of high-strength quenched and tempered alloy steel plates intended for use in fusion welded boilers and other pressure vessels. The steel shall be killed and shall conform to the fine austenitic grain size requirement. Under this specification, the plate thickness determines the grade selection and the mechanical properties.   A517 grade A steel pates 2.5" in thickness and under, will have minimum Yield Strength of 100 ksi.  A517 grade b steel plates over 2.5" in thickness will have a minimum Yield strength of 90 ksi.  Typical applications include unfired vessels and tanks. ASTM A517 Grade A plates are Pressure Vessel Plate and supplied in the as-rolled condition. The ASTM A517 Gr. A plate may be ordered normalized or stress relieved, or both. ASTM A517 Grade H are Pressure Vessel Plate and supplied in the as-rolled condition. The ASTM A517 Gr. H Plate may be ordered normalized or stress relieved, or both. AS
阅读全文

20G boiler steel pipe

-
图片
Boiler operation status of the GB/T 5310 20G boiler steel pipe  Some steel companies produce the fake 20G boiler steel pipe cause the huge problems. Because the creep resistance of 20G boiler steel pipe is lower than other steel pipes and the 20G boiler steel pipe is overheated, the 20G boiler steel pipe wall metal overheated for a long time, which results in accelerated creep at high temperature, decreased strength, and finally the early creep burst occurred. During 20G boiler steel pipe fracture analysis, it was found that the macroscopic surface of the 20G boiler steel pipe fracture was covered with thin blue-purple oxide film, which indicated that the temperature of the 20G boiler steel pipe burst was 800℃, and the section was not smooth due to the effect of high temperature oxidation. There is a thick oxide layer on the inner surface of the  20G boiler steel pipe . The structure of the oxide layer has three layers and usually only when the ambient temperature
阅读全文

S235JR steel plate

-
图片
Katalor has more useful S235JR steel plate information S235JR steel plate  is a kind steel grade and it is mainly used for steel structural buildings, frames and other steel body under the standard of EN 10025-2.  S235JR steel plate  is for low temperature impacting test under zero centigree. Katalor steel Industrial specialized in S235JR steel plate  in china many decades years. The composition characteristics of S235JR steel plate  are low carbon, less than 0.20%, low alloy and total alloy element less than 3%. Low carbon content in S235JR steel plate  steel is to meet the technical requirements of plasticity, toughness, weldability and cold deformation of S235JR steel plate  used for engineering structural parts. The S235JR steel plate  has Mn as the main additive and conforms to the resource characteristics of our country. Mn not only has a significant strengthening effect on ferrite , but also reduces the cold and brittle temperature of the S235JR steel plate , and
阅读全文